How to glue rubber boots? Methods for repairing rubber shoes. Actual: how to seal rubber boots at home? Repairing leather boots

Rubber boots are shoes that are necessary not only for summer cottages, but also for the city. They protect from bad weather and dirt. But they have one drawback - any nail or piece of glass is enough for the shoes to become unusable. Of course, the easiest way would be to simply take the shoes in for repair, paying a tidy sum at the same time, but here we also face a problem: not all shoe shops undertake to glue rubber boots, because they themselves do not know how to do it.

Seal rubber boots at home can be very difficult. This can be confirmed by everyone who has ever tried to do this. The fact is that the usual glue that we use to glue ordinary shoes will not work for rubber boots. It does not matter if you want to seal the seam, the sole or any other part of the boot.

To seal rubber boots effectively, you need to know where the damage is. Rubber is a material that is very easy to pierce with a sharp object. You can simply step on glass or a sharp brick so that a through hole forms in the sole. This is a very unpleasant phenomenon, as water will rapidly accumulate in the shoes. But if we find damage, we can fix it at home.

And there are several methods by which this can be done. Let's take a closer look at how to seal rubber boots.

Tips before gluing boots

In order for the repair to be successful, and the boots to last for a very long time, you need to know the following:

Before repair, rubber shoes must be very thoroughly cleaned, washed and dried.
- The patch can be cut from a tire or old rubber boots.
- It is better to carefully process the patch from the wrong side with sandpaper or a file to make the surface rough for better adhesion of the glue.
- It is best to degrease the surface of the shoe with acetone or a solvent.
- Glue must be chosen special, on which it is necessarily indicated, for example, “shoe” or “rubber”.
- Before repairing rubber boots, it is imperative to read the instructions from the adhesive manufacturer in order to do everything correctly.
- It is best to smear the patch and the place of gluing with special glue several times, after waiting until the first layer dries a little.
- When gluing the surfaces, it is necessary to press very strongly against each other or tap on the place of gluing with a hammer.
- The patch on the boot can be easily disguised with sandpaper.

4 ways to seal rubber boots

Method 1. You can stick boots special glue . It can be purchased in shops for hunters and fishermen. But in order to get the right glue, you need to know what exactly the shoes are made of. The fact is that for shoes made of EVA or polyurethane, different adhesives are needed.

The seller can help you purchase the necessary glue by giving advice. Further, everything is simple - you need to sand and degrease part of the boot and stick a patch. If the shoes are made of porous material, then you can glue it without using a patch. The edges at the site of the cut should simply be turned out, generously smeared with glue and pressed against each other.

Method 2. For this method, you will need a regular bicycle repair kit . It contains patches on special protective films, sandpaper and, of course, glue. Clean the desired place on the shoes with sandpaper and thoroughly degrease. Further, having previously removed the film from the bookmark, it is necessary to apply glue to it and press the patch to the hole. You can use shoes almost immediately, but it is better to wait at least 12 hours.

The only drawback of the method is the unaesthetic appearance of the shoes after the repair. If the hole appeared not on the top, but on the sole, the gluing technology does not change. You just need to make the surface smooth and even, because usually the sole on such shoes is quite embossed. This is possible with a sharpening machine. And then stick a patch on this place.

But it is important to know that such a patch will not last long, especially if the sole of the boots comes into contact with a rough and hard surface very often. Therefore, it is better to wear such boots, for example, for fishing. Well, if the sole breaks again, the gluing procedure will need to be repeated.

Method 3. In order to seal women's boots without using patches, you need to purchase adhesive sealant . You can do this at any auto shop. First you need to degrease the place of gluing, and then grease the torn edges with glue and press them together. If you do everything carefully, then the boots will look like new.

Method 4. This method of repairing rubber shoes is also called "hot" method . It is not difficult, but requires certain skills and, most importantly, a vulcanizer. As a patch, rubber pre-soaked in gasoline is used. It is placed on the hole in the boot and clamped with a vulcanizer. The device must be turned on for 20-30 minutes, then turned off and cool. Only after it has cooled down, you can remove the press.

Do not despair if your favorite rubber boots are suddenly torn. It is enough to make a little effort and the repaired boots will be no different from new shoes. You can use sealed boots a day after the patch has been applied. But if there is no time to wait, then you can walk in them in an hour.

How to care for boots

Rubber boots need to be properly cared for. And then you do not have to resort to their frequent repairs. After all, even the high quality that the manufacturer guarantees does not always mean the safety of shoes.

Rubber boots need to be cleaned properly. They are best washed with a solution of glycerin and water. In this case, the boots should be wiped with a soft cloth and dried frequently so that the fungus does not appear.

Wet rubber boots should not be dried with a hair dryer or battery. Shoes need to dry naturally.

In holey shoes, a person feels extremely uncomfortable, even if the puncture is not visible from the outside. This, of course, is an excellent reason to buy new boots, but such an opportunity is not always available. But even if it is, do not rush to throw away the damaged pair. It is very possible that she will still serve. How to glue boots? Read about it in our article.

Which shoes are broken?

It's no secret that the repair of rubber boots is different from the repair of leather boots, but it has some similarities with gluing shoes made of PVC or a waterproof material called "EVA". Leather shoes can sometimes be sewn up, and this is better than putting a patch on glue, but nothing like this can be done with rubber shoes - glue, only glue, and no extra punctures!

The repair method may also depend on which part of the boot the hole was found in:

in the sole;
the upper came off the sole;
on the smooth part of the top;
on the boot;
at the seams.

Are there any prospects?

The first option is the hardest. The sole rubs and experiences serious mechanical stress, so the connection must be strong. Most often, a hole appears because a person stepped on a nail or something similar.

Important! It is possible to seal the hole, but it is unlikely that it will be possible to do it in such a way that the boots are enough for a few more seasons. Worst case, they'll last a month.

Peeled top - also a bad option. Friction is less, mechanical loads too, but they are enough for a newly repaired shoe to fall apart again after a couple of times. Better - if there is even the slightest opportunity to sew the top to the sole at least in this place.

Light damage

A hole in the smooth part of the top and shaft is usually sealed quite easily and the patch lasts a long time. In this case, it is very important to choose the right glue. This is especially true if the hole is at the bottom, which gets water and dirt.
A hole in the top appears if you ran into rebar sticking out of the ground or ran into a nail that crawled out of the wall. In this case, there are almost no mechanical loads on the gluing site, so you can also think about aesthetics - make a patch that will not be very noticeable (or vice versa - turn it into a decorative element).
A torn seam is also repaired quite simply. This defect is typical, of course, for leather shoes or leatherette boots. The seam will hold up better than the glue.

Repairing leather boots

It is better to take expensive model shoes to the workshop. True, repairs are sometimes more expensive than a new pair, so each case must be approached individually. But patching the top can also be considered a minor repair, so it's relatively inexpensive.

Choosing glue

The first thought that comes to mind when you need to glue a small but important detail is to use superglue. In this case, it is better to discard this idea immediately. The glue, of course, dries quickly, but it has a bad effect on the structure of the skin or leatherette, the gluing site becomes fragile.

Important! When you try to walk in boots repaired like this, the hole will simply increase, and its edges will become brittle.

Professional adhesives are suitable for you:

"Dismakol";
"Nairit".

These are the compounds used by professional shoemakers. They are not always on sale, and it is best to look for them in stores that sell leather scraps and other goods for arts and crafts. If there is no such specialized store nearby, Moment Marathon or another elastic compound will help you out.

Important! Before starting work, be sure to read the instructions and act in strict accordance with it.

If the seam on the shaft is torn

In this case, you do not need glue at all. You need:

thick nylon threads;
needle;
awl;
plank;
blade.

Important! An awl and a plank are needed just in case the needle does not fit into the existing holes.

Sew up:

Additional holes do not need to be made, they reduce the strength of the product.
Carefully support the lining with a blade.
Thread the needle, fold it in half and make a knot at the end.
Insert the needle from the wrong side into the extreme hole.
Pull the thread to the front side.
Insert the needle into the outermost hole on the opposite side of the seam.
Pull the thread through until the stitch flattens out on the outside, but don't pull too hard - the nylon thread can tear the leather.
Insert the needle from the wrong side into the second hole on the side you started sewing from.
Make a second stitch - into the second hole on the opposite side.
Having finished the seam, bring the thread to the wrong side and fasten in any convenient way (you can even melt it).

We glue the seam

Many modern models look like sewn, but in fact the seams on them are purely decorative, and gluing provides strength. In this case, stitching the hole is useless. It's better to act like this:

Cut 2 strips of leather 1 cm longer than the hole.
Glue them to each side of the seam to leave a 0.5 cm allowance.
Glue the allowances together or sew with nylon threads.

Top torn in place

The most unpleasant option is that any patch pasted on the outside will be perfectly visible. There are two options:

stick a patch from the inside;
stick on the outside, making an application,

Important! In the second case, you will have to repair another boot, even if it is completely intact. Therefore, the skin on the patch needs twice as much.

Option 1

A piece of leather, pasted over from the inside, is in contact with the leg and may begin to rub. Therefore, the patch should be made of thin leather or even waterproof fabric:

raincoat fabrics;
bologna;
of the adviser.

But the size of the flap can be anything. To glue the boots, proceed as follows:

If possible, turn the boot inside out.
Cut out the patch so that it completely covers the puncture and there are still allowances on all sides.
Apply glue around the hole at a distance of 3-5 mm from the edge.
Attach the patch from the wrong side.
Match the edges of the hole and press.
Turn the boot right side out.
Carefully grease the edges that are not glued with glue (you can use a cotton swab).
Press the edges well.
Remove excess glue immediately.

Option 2

It is much simpler than the previous one, because all the work is done on the front side:

Cut out 2 identical leather pieces - matching or contrasting.
Lubricate them with glue.
Close the hole with one piece, glue the other symmetrically to the second boot.

Torn out sole

In this case, a tube of glue and a small piece of skin will not get off. You will also need:

skin;
acetone or white spirit;
wire or elastic bandage.

Before sticking boots at home, put them in order. Shoes must be clean and dry.

Clean the gap from the old glue.
Go over it with a fine sandpaper.
Degrease surfaces with white spirit or acetone.
Apply glue according to instructions.
Press the parts tightly against each other - they can be wound with wire or bandaged with an elastic bandage.
Wait for the glue to set - this usually takes a day.

Hole in the sole

If you stepped on a thick nail, your shoes will also have to be sealed. You will need:

epoxy resin;
patch material;
scissors or a sharp knife.

The place of the gap is best filled. Epoxy is suitable for both leather and plastic soles:

We direct the composition according to the instructions on the package.
We fill the hole.
Let's solidify.
From above, close the puncture site with a patch or insole.

How to care for leather boots?

No one is safe from some damage - anyone, even the most accurate person, can fly into a rebar or a nail. But sometimes boots crack and tear simply from improper care:

After you have come from the street, put your shoes in order - clean them of dirt and dry them.
Clean leather boots regularly with cream.
Periodically lubricate your shoes with castor oil.

Important! If you need to put boots or shoes for long-term storage, do not forget to stuff them with napkins or newsprint. Napkins will also help you out when drying - stuffing the socks of your boots with them, you can be sure that the shoes will not lose their shape.

How to fix rubber boots?

It seems to many that repairing rubber boots with their own hands is impossible, it is better to immediately throw them away and buy new ones. This is not entirely true. Shoes will last you a very long time if you carefully seal them, and before you get down to business, follow a few simple steps:

Wash your boots thoroughly.
Dry them well.

What to make a payment from?

There is always a piece of leather in the house of a needlewoman, but where can I get a piece of rubber? Nothing complicated. You will be rescued:

old bicycle tire;
old rubber boots;
a hammer;
piece of rubberized fabric.

You also need rubber glue (you can use universal shoe glue if you can get them), as well as fine sandpaper or a file.

Important! Rubber gloves or old rubber toys will not work for you: the former are too thin, and the latter are made from a different grade that exfoliates.

Let's start repairing

The rubber patch can be cut out simply with sharp scissors. It should be larger than the hole, but not by much. Unlike leather shoes, which sometimes diverge simply because the threads have rotted, a hole in rubber boots most often appears from mechanical damage. Therefore, you can easily run into a situation where a piece is simply torn out and it will not be possible to combine the edges.

It is better to glue on the front side, acting in this way:

Cut out the patch.
Treat the wrong side of the workpiece with sandpaper or a file - this is necessary so that the surface becomes rough, then it will hold better.
Wipe the surfaces to be glued with acetone or mineral spirits.
Lubricate both surfaces with glue according to the instructions.
Press the patch firmly against the boot.
Tap the gluing area with a hammer.
When everything is dry, go over the seams with sandpaper to make the glued area uniform and mask the patch.

How to seal PVC boots at home?

In everyday life, all boots made of waterproof materials are usually called rubber. However, this is not the case. For the manufacture of such shoes, PVC, polyurethane, and EVA are used.

The repair technology in all cases will be the same as when working with rubber, but a different glue is needed. It should indicate what kind of material it is intended for. And, of course, when buying boots, it is very useful to remember what they are made of - there may not be markings on such products, but on the price tag in the store it usually is.

Repair without a patch

Waterproof shoes can be repaired without a patch:

Turn the edges of the hole outward.
Lubricate them well with glue.
Press the edges together so that there is no gap between them.

We use a repair kit

If you have rubber boots in which you go hunting or fishing, buy a regular bicycle repair kit, with which you can repair shoes in the field. The kit contains ready-made patches on special protective films. In addition, there you will find glue (designed specifically for this material) and a piece of sandpaper of the desired fraction. The boot is sealed in the same way as with a self-cut piece of rubber, only it is not necessary to degrease the patch, because it has a protective film that must be removed.

Important! The hole on the sole is closed in the same way as on the shaft.

Women's rubber boots

Rubber boots are worn not only by hunters and fishermen. They can be seen on the capital's fashionistas. However, stylish boots are torn no less than those in which lovers of extreme recreation go.

But in this case, it is important that the gluing place is not noticeable, and the boots retain their attractive appearance. Silicone sealant will help you out:

Degrease the bonding area with acetone or other compound.
Lubricate the edges of the hole with sealant.
Press them firmly against each other.

Curing

The most reliable way to repair rubber shoes. But it requires determination, certain skills and special equipment - a vulcanizer:

The flap, before sticking, you need to hold a little in gasoline.
Apply a patch to the hole.
Clamp the entire structure with a press.
Turn on the vulcanizer and let it work for about half an hour.
Turn off the vulcanizer.
Let it cool completely.
Remove the press.

Two words about care

Rubber boots are an unpretentious product. However, it also needs care:

After you take off your boots, wash them well and dry them.
Pay special attention to the lining - if it is not dried well enough, it will begin to rot and tear quickly.
From time to time, wipe rubber products with a cloth soaked in glycerin.

footage

In this article, we told you about all the ways to repair boots from a variety of materials. Now, we hope that in any situation you can find the right solution and fix your shoes with the help of improvised means.

Recently, rubber boots have been used not only in the country, on hikes or in the forest. Today it is fashionable and stylish footwear that saves during heavy rains and floods. Shops are full of bright and colorful boots. However, even such strong and stable shoes can suffer and deteriorate.

The most common problem is a punctured sole. When stepping on a shard, broken glass, or even an ordinary pushpin, a hole forms in the rubber. It is very easy to pierce the rubber material, as a result they begin to leak and are not usable.

But do not rush to throw out the shoes, in some cases the shoes can still be repaired. Let's find out how to seal rubber boots at home, how to close a hole in the sole and bootleg.

How to prepare boots for repair

First, the boots must be thoroughly cleaned, washed and dried. You can seal shoes with rubber or a patch from old rubber shoes or tires. To do this, cut out the necessary piece of rubber and process on each side with a file or sandpaper. The resulting rough surface is stronger and more secure with glue.

Choose a special glue marked “rubber” or “shoe”. By the way, you can find a tool for gluing rubber boots in an automobile store or stores for anglers and hunters.

Perfectly fit take glue-sealant. When choosing a product, consider the material of the shoe, as EVA and polyurethane require different products. In no case do not use classic PVA or “Moment”!

Dried boots should be sanded and degreased with acetone or solvent. Before using the glue, be sure to read the instructions and follow the recommendations.

If the sole is torn, and not the bootleg, you must first make the surface smooth and even with a sharpening machine. And then you can glue the patch. Next, let's take a closer look at how to seal the sole and shaft quickly and efficiently.

Five ways to seal boots

“Hot” bonding method using a vulcanizer. As a patch, they take rubber, which is pre-soaked in gasoline. The resulting patch is placed on the hole, clamped with a vulcanizer and left for half an hour. Then the device is switched off and cooled. Only after that you can remove the press;
A standard bicycle repair kit will help you fix rubber shoes, which includes special patches based on protective films, glue and sandpaper. Clean the desired area on the boots with sandpaper and degrease. Then remove the film from the bookmark, apply glue and stick to the desired location. It is advisable to wait 6-12 hours and only then use the shoes. However, the appearance of the glued patch is not very aesthetic, so this method is suitable for repairing the sole or for using boots in places where appearance does not matter.
We repair boots using a special tool for gluing rubber shoes. This is the easiest and most affordable method. First you need to prepare the patch and boots for gluing. Do not forget to degrease the shoe surface. Apply several layers of glue to the patch and the bonding area and apply each layer after the previous one has dried slightly. Firmly and firmly press the surfaces to be bonded together. For effectiveness, you can tap with a hammer on the bonding area. To prevent the patch from being conspicuous, treat the surface on the sealed area with sandpaper;
If the boots have a porous surface, you can patch the holes without a patch. In this case, the edges at the site of the cut are turned inside out and liberally smeared with glue, and then strongly pressed against each other;
When using glue-sealant, which is sold in auto shops, you can also repair shoes without a patch. First degrease the bonded areas, then grease the torn edges and press firmly together.

How to take care of rubber boots

If you choose the right glue and carry out the procedure carefully, you will be satisfied with the repair. And in order for the boots to last longer, you need to organize the proper care of rubber shoes and repaired products. Thoroughly clean and wash boots under running water after use.

We offer a few simple rules for the care and use of rubber shoes:

Wipe the outside of the rubber surface with a clean cloth. Wash very dirty shoes first in water and then dry them;
Colored boots are cleaned with Vaseline. It will retain color and shine, while the boots will not burst and become cracked;
Be sure to use shoe insoles, preferably warm ones. Wash the insoles every two to three months;
Do not wear rubber boots in hot sunny weather, as rubber deteriorates and burns out;
Periodically lubricate the surface of the products with oil varnish with rubber glue or glycerin. This will keep the boots shiny;
Before long-term storage, be sure to lubricate the shoes with glycerin. Then wrap the products in newspaper or paper and put them in a cool, dry place;
You can remove dark spots and stripes from rubber using a regular school eraser. It should be soft and clean;
If your foot does not fit into the narrow shaft of the boot, lower the elastic stocking inward and put on the shoes. Then the leg will fit in without problems, and after that it is easy to pull out the stocking.

To keep shoes shiny and attractive for longer, lubricate the surface with oil varnish with rubber glue or wipe with a damp cloth with glycerin. By the way, glycerin is an excellent leather care product. It will help to smooth a jacket made of genuine leather and give the product a presentable appearance. Read more on how to care for a leather jacket.

Shoes tend to wear out quickly, and to save your budget, you can try to do your own shoe repair. This will require a special tool and a little skill. This article describes in detail how you can repair shoes yourself.

Tools and materials for shoe repair

The upper of the shoe is repaired with a homemade hook. These hooks are made from thick machine needles. The eye of the needle must be cut with a diamond tool (diamond cutting disc, needle file, etc.) and secured in the handle.

To hem the bottom of the shoe, you will need a thick shoe hook. To make holes in the sole, you will need an awl. It is good if there are several of them (different thickness and configuration).

For some operations, shoe needles will be needed. To make them, you will need a thin balalaika string and lead-tin solder for soldering.
With all the above tools, you can easily do your own shoe repair. But in addition to tools, you will have to stock up on some auxiliary materials.
To sew the upper of the shoe, you will need precise six-complex cotton threads in six layers. Sometimes you can use ordinary threads in three layers or kapron.
The bottom of the shoe is hemmed with special linen threads (draft). Sometimes they are additionally rubbed with shoe pitch.
Before gluing or welding shoe parts, they are pre-degreased with pure gasoline.
Also, for general purposes, you will need a medium-grained abrasive skin, cloves, pliers, wire cutters.

Do-it-yourself shoe upper seam repair

Shoe repair in this case can be done with a regular needle and thread (if convenient). In an inconvenient place, it is better to sew with a special hook. The hook must be inserted from the outside, put a thread on it and pull one end out. Then insert the hook into the second hole and pull the loop out. After that, the end of the thread must be inserted into the loop and tightened into a stitch. So sew to the end.

If the sole is peeled off

Do-it-yourself shoe sole repair in this case can be in two versions, depending on the sole (rubber or polyurethane).

Shoes with rubber soles must be cleaned of dirt and grease. Apply glue to the workpiece and to the sole, let it dry a little and press the boot. Crimping occurs according to the following scheme: the boot must be stuffed with newsprint and placed in an inflated football chamber with a nipple. There you need to withstand the boot for about 10 hours.

Shoes with polyurethane soles also need to be cleaned and degreased. Remove the top layer of skin with a flat file, and degrease again. Cut off a small piece of polyurethane from the old sole and smear it over the gluing site with a hot electric soldering iron. After that, press the sole to the top of the boot and hold it with a hot burning device.

If the top of the boot, which is adjacent to the sole, is torn

Using a flat screwdriver, you need to disconnect the upper from the sole, clean and degrease everything. Prepare a patch: it should be about 15 mm larger than the torn area. From the inside, the patch must be cut to nothing with a one-sided sharpening knife (the cut should be about 8 mm thick).

The place on the boot where the patch will be is sanded with a flat file. The patch must be degreased and dried. Then glue the patch to the top of the shoe, dry it. Lubricate the lower part of the patch and the place between the sole and the boot with glue, fill the patch there, dry it and press it.

Do-it-yourself heel repair

To glue a heel on a rubber heel, on the one hand it is treated with a rasp, making it rough. The heel is leveled with a rasp. Everything needs to be degreased, smeared with glue on the heel and heel, glued and trimmed.

To change the heel on a leather heel, the same actions are performed, only the heel needs to be additionally pierced with nails (9-10 pieces).

Repair of heels on women's shoes. Wide and not too high heels are repaired in the same way as described above. The heel is broken through with 3-5 nails.

On thin high heels (stiletto heels), the metal and metal-plastic heels change. The old heel must be removed, and a new one must be installed on the heel. To do this, there are landing holes in the heel, and pins on the heels.

Thus, you can easily repair shoes with your own hands, giving your shoes a second life.

Almost everyone has a pair of rubber boots in their wardrobe. Like any thing, rubber shoes crack over time. In order not to throw away your favorite pair, you can try to repair it. How to seal rubber boots is described in the article.

Preparing boots for repair

A nail, a small shard of glass, or even a pebble with a sharp edge is enough to damage rubber shoes. One wrong move and the boot could crack.

Repair shops do not accept rubber shoes. This means that damaged boots can either be thrown away or repaired yourself.

How to seal rubber boots is a common question, the answer to which lies in the knowledge of some of the features of such repairs.

First you need to determine the location of the puncture or crack. To do this, you can take a container of water and a damaged boot. Roll up the freebie, starting at the top, like a tube of toothpaste. You should get a tight bundle. Next, lower the sole into the water. Air will escape from the puncture site, forming bubbles.

The next stage of preparation is the obligatory cleaning of boots from dirt and dust, degreasing and drying. Drying shoes is recommended to be carried out away from heat sources. Drying rubber boots on batteries can cause deformation, which will spoil their appearance and complicate the restoration process. All manipulations should be carried out carefully so as not to increase the size of the damage.

Then you should accurately determine the material from which the boots are made. Modern rubber shoes for women are made not only from rubber, but also from polyurethane, ethylene vinyl acetate (EVA). Each of these materials requires a different adhesive.

If it is difficult to determine the material of the boots yourself, you can take them with you to the store, where a specialist can quickly determine what the shoes are made of.

How to glue rubber boots

For gluing cracks on rubber boots, many people immediately buy a universal strong adhesive adhesive, known as Moment. In fact, the composition of this product not only does not stick rubber, but can also ruin it. It will not be possible to achieve a good result with ordinary glue.

Repair of rubber boots should be carried out with special adhesives. High-quality products can be found in automotive and fishing stores. In this case, it is possible to purchase adhesives with a hermetic effect. They allow you to reliably glue cracks of any size and at the same time protect shoes from leakage.

The choice of a suitable adhesive depends on the technology of work. To date, there are several methods for the restoration of rubber shoes.

Anglers Method

Fishing and hunting stores sell special ones. They contain instructions that describe in detail the technology for using the product. For rubber boots, it is generally recommended to sand the damaged surface and apply a patch.

How to seal rubber boots if they are made of EVA? This material has a porous structure into which the adhesive is absorbed. No patches are needed to repair these boots. It is enough to apply the required amount of glue on the crack lines and press firmly. The hardening time of the product is indicated by the manufacturer on the packaging. After gluing, the boots will look like new, and the place with a defect will remain invisible.

The cyclist method

This method has been tested by many cyclists who often face the problem of a broken camera. For wheel repair, a bicycle repair kit is mainly used, consisting of patches on protective films, special glue for rubber and sandpaper.

According to this technology, it is necessary to rub the place where the patch will be applied with sandpaper, degrease with acetone and evenly apply glue. After a few minutes, you need to apply a patch and press firmly.

The bicycle repair method is reliable and guarantees high tightness. You can use glued boots almost immediately.

The disadvantage of this method is the unaesthetic appearance of the repaired product. A bicycle patch remains at the place of gluing, which is impossible not to notice. Therefore, in this way it is better to glue boots for summer cottages or fishing.

Automotive method

Many women ask how to seal rubber boots at the fold so that it is not noticeable. Boots made of rubber or EVA most often crack along the fold lines. A patch in such places is not always suitable and can spoil the appearance. Rubber shoes for women require a more careful repair, which can provide an elastic adhesive-sealant. It has a colorless viscous structure and is ideal for repairing colored and transparent rubber boots.

Today on sale there are automotive adhesives from different manufacturers. One of the best is Done Deal's Crazy Hands sealant. You can buy glue of this brand at any store for motorists.

Before applying the elastic bonding agent, it is necessary to treat the puncture or crack with acetone. After drying, apply glue.

Features of gluing the sole

Rubber shoes can be damaged in the sole area. How to seal a cut on a rubber boot? In this case, you can use any of the methods described above. Only preparation for gluing should take place a little differently. First of all, it is necessary to process the place of the cut on the grinding machine. The surface to be treated must be perfectly smooth. If this step is missed, the repair will not give a good result. Next, you should adhere to the technology of the chosen method.

To repair the sole, it is better to use adhesive sealants. Applying a patch in this place will not give a lasting result. When walking, the patch will quickly wear out, and soon there will be a need to replace it.

In order for the repaired shoes to serve as long as possible, it is important to know not only how to glue rubber boots, but also how to care for them.

Periodically wipe the shoes with a soft cloth moistened with a water-glycerin solution.
Dry rubber boots at room temperature away from batteries. Under the influence of hot air, the glued parts can become porous. As a result, the shoes may leak again.
Every time after a walk, clean your boots with a damp cloth. Dirt and dust can eat into the rubber, leaving stains. They are especially noticeable on light-colored shoes.
It is better to store rubber boots in a cardboard box. For this purpose, it is recommended to keep the packaging in which they were sold.