What can be done from a lampshade from a floor lamp. How to make a lampshade with your own hands from fabric. Paper plate lampshade

Their range is very wide and different in purpose, size, shape. According to the type of material used for the manufacture of the following lampshades are distinguished:

How to sew a lampshade on a floor lamp

All it takes to create a lampshade is an idea, material and patience. First, let's look at how to make a fabric lampshade. First of all, choose what material you want to sew. Suitable silk, linen, taffeta, cotton. Don't forget about the color of matter. It should be combined with the decor of the room (furniture upholstery, curtains, carpets). Although this is not essential.

So, you have chosen the fabric and decided on the color scheme. Get another new lampshade and prepare clothespins, a centimeter, crayon, pattern paper, a simple pencil, and scissors for work. Now take your measurements for the pattern. Measure the top and bottom circumferences of the lampshade and the sides. Add a few inches for seams and hemlines. Connect the lines. Cut out.

Lay out the pattern on the fabric and circle with chalk. Cut out carefully. Apply glue with a gun in a small amount to the fabric, and then to the lampshade. Now wrap the fabric around the frame and gently straighten it with your fingers. All is ready!

Today, do-it-yourself lampshades for a floor lamp are valued no less than factory ones. The guests of your house will notice and appreciate such a piece of your decor. But it is not necessary to buy a new lampshade. If you have an old one, then you can simply restore it. To learn how to update a floor lamp shade, read the following master class. You will understand how you can transform a lighting fixture with the help of ordinary materials and accessories.

How to update an old lighting fixture

You will need:

Pencil;

Fabric (of your choice)

Scissors;

Floor lamp with lampshade;

Satin tape;

Large sheet (newspaper);

Several pieces of pins;

Spray glue (or regular fabric glue).

First, disconnect the wire. Remove the old lampshade from the floor lamp. Leave only the base. Lay the frame on its side on a large sheet. Outline the top and bottom edges with a simple pencil, rolling over the paper. Connect both lines. Cut out the pattern, do not forget to add one centimeter on each side.

Spray the underside of the fabric with spray glue (you can use fabric glue diluted with water, apply it with a brush). Then place the base on the fabric and roll slowly, pressing and smoothing towards the edges. Cut off excess fabric.

Now work on the top and bottom edges. Tape them with ribbon, fringe or braid. When the glue dries, insert the lampshade into the floor lamp and turn on the light. You can decorate the product with buttons, appliqués and whatever your imagination desires.

If you have an unnecessary woolen one at home, then use it to update the lampshade. Cut a rectangle out of it (depending on the size of the frame). Cover the frame with them, securing with pins. Bend the edges under the rim of the lampshade. Fix with a heat gun.

How to crochet

This lamp will update your interior and will be a great night light in your bedroom. You will need:

Frame for lampshade;

Two skeins of wool (you can have different colors);

Hook #3;

Scissors.

The diameter of the lampshade is 26 centimeters. Cast on a chain of 52 stitches. Then connect into a ring. Continue knitting according to the scheme in rows:

First: Cast on double crochets (CH).

Second: CH, five air loops (VP).

Third: four CH, one VP.

Fourth: two single crochet (SB), six VP.

Fifth: three CHs, eight VPs.

From the sixth to the eleventh: three SBs, ten VPs.

In the twelfth to thirteenth: four CH, five VP.

Fourteenth: five CH, VP and CH each.

Knit the entire last row in SB. Close all loops. The knitted lampshade for the floor lamp is ready. It can be improved, transformed and supplemented with various accessories. Show your creative imagination.

How to make a lampshade for a floor lamp from napkins

To make it, you need to stock up on lace napkins, glue and a base. If you don't have a frame, you can make your own. Inflate the balloon to the correct size. If everything you need is prepared, then proceed. Soak the napkins well with PVA glue and immediately glue the ball over. In the place where the light bulb will be inserted, leave a small space. When the workpiece is dry, pierce the ball with a needle and remove the remnants. It turned out such an original element of decor.

Such a floor lamp will fit perfectly into the rooms.

If you do not have extra openwork napkins, then read a master class on how to knit them just below.

How to knit a napkin

You will need hook number 1 and acrylic yarn. The napkin should be rounded. So, dial twelve VP. Connect in a ring. Tie it with single crochets. In the second row, dial three loops for lifting and knit air loops to the end. Next, make three VPs, four CHs above the columns of the previous row. Repeat to the end of the chain.

The next row for beginners will be difficult, be careful (alternate the indicated loops in all rows). We knit five VP and eight CH. In the next row, dial nine VP and 10 CH. Next, knit a row of eleven VPs and four CHs. Proceed to complete the knitting of the napkin. Knit five VPs, fifteen CHs in the VP of the previous row. When finished wet and stretch. Leave it to dry like this. You can starch the napkins to keep their shape better.

Do-it-yourself lampshades for a floor lamp can be knitted, crocheted, sewn from fabric or woven using the macrame technique. Creating a new accessory is a great way to freshen up the interior of your home.

Good luck in job!

Every housewife wants to make her house extraordinarily beautiful. Some decorate it in some unusual style, for example, Provence, country or minimalism. Someone is trying to decorate with decorative elements. Others focus on one element, for example, a lampshade or a ceiling.

Consider the options for how to make a do-it-yourself ceiling lamp for a chandelier. To do this, you will need not some rare, but ordinary improvised means.

Option number 1: paper

The easiest way is to make an original paper lampshade. Such a decor element can have any shape. It will harmoniously fit almost any interior - in the kitchen, in the living room, in the nursery. It is worth remembering that the life of a paper lampshade for a lamp depends on the quality of the paper. It should not be too thin, but at the same time light-transmitting.

The easiest way is to consider how to make a lampshade with your own hands from the wallpaper left over from the repair. Consider how to make a product in the form of an accordion. The workflow does not take much time and does not require any special skills, abilities or schemes. From the wallpaper you can make a lampshade for a floor lamp with your own hands, for a table lamp or sconce:

First you need to prepare the material - a piece of wallpaper 1.5 m long and approximately 30 cm wide.
Mark the ribs with a pencil or pen.
Carefully form an accordion. The width of each rib should not exceed 3 cm.
Using a hole punch, make holes in the accordion.
Pass a decorative cord through the holes and glue the lampshade along the side seam.

Even a child can make such a product on their own.

In the process, instead of wallpaper, you can use rice paper. With it, you can update the old lampshade. Wrapped with such paper, it will look stylish and modern. You can decorate the product with the help of such decorative elements as special stamps, stickers, etc.

Do-it-yourself paper lampshades will decorate any interior in style. The main thing is to choose the right color scheme and shape.

Option number 2: rope

A do-it-yourself lampshade made of rope will look original. It can be used to decorate any lamp: sconces, floor lamps and others.

First you need to prepare the necessary tools and materials:

20 meters of rope;
1 balloon for the base;
PVA glue;
white paint (preferably in a spray can);
duct tape;
gloves (ordinary household or medical);
weaving device (special board or perfume box).

It is quite easy to make such a lampshade with your own hands:

Using a weaving board, make a decorative ribbon out of the rope. Its lines can be smooth or curved - as your fantasy tells you.
Now you need to glue the balloon filled with air with tape.
Taking the top of the ball as a reference point, lay the rope in smooth turns. At the same time lubricate it with glue.
Remove the cover from the lamp. Paint it white. Put on a finished lampshade from above.
Paste the ball completely and grease with glue again.
Poke the ball with a needle and pull it out. After that, a form woven from a rope will remain.

A do-it-yourself twine, twine or rope lampshade is suitable for a table lamp, sconce or floor lamp. Under it, it is recommended to use an LED lamp, which will not heat up such a ceiling very much.

Option number 3: threads

Another option is a do-it-yourself lampshade made of threads. Self-made chandeliers from threads look very original. They attract attention and fit perfectly into any interior.

You will need:

balloon;
cotton threads of one or more colors;
250 ml of PVA glue;
suspension cord;
energy saving lamp;
scissors;
large needle;
oilcloth or plastic the size of an A3 sheet;
petrolatum;
tassel;
cotton pad and stick.

The process of making a lampshade for a table lamp, sconce, chandelier or floor lamp from threads with your own hands consists of several stages:

Blow up the ball. It is desirable that its size be from 25 cm.
Lubricate its surface with Vaseline.
Cover the work surface with paper or oilcloth.
Closer to the bottom of the tube with glue, pierce a hole.
Wrap the ball with threads in any order.
Lubricate the threads with glue. Leave to dry completely overnight.
Using a cotton swab, separate the balloon, deflate and pull it out.
In the upper part of the finished product, make a hole for the lamp and cartridge.
Insert the lamp inside. Fix the holder for the cartridge in the hole.

Now just hang the finished lampshade in the place intended for it.

Option number 4: lace

You can try to make a lampshade out of lace with your own hands. From this material you can make a lampshade for an old table lamp with your own hands, for a wall lamp or a floor lamp.

Work begins with the preparation of the things necessary for work. This is actually lace, PVA glue with a brush, a balloon and electrical elements for the lamp.

Stages of work:

The first stage is the preparation of lace. It is necessary to cut several circles of different sizes.
Blow up the ball. Lubricate its surface with glue.
Attach lace circles to the ball. It needs to be done with a twist.
Leave the product until completely dry. This will take about a day.
Pop the balloon and pull it out.
Fasten the socket, lamp and wires. It is recommended to use low power lamps that will not heat up the lace.

Option number 5: macrame

Fans of original decorative elements will undoubtedly pay attention to the macramé lampshade.

To make macrame lampshades with your own hands, you need to prepare:

172 m of 3 mm thick cord;
metal tubes and rings for the frame;
8 rings with a diameter of 7.5 cm;
1 ring with a diameter of 17 cm;
1 ring with a diameter of 36 cm.

How to make a frame for a lampshade with your own hands? We connect together two rings (17 and 36 cm in diameter) and 8 metal tubes 27 cm long.

The workflow for making the plafond itself looks something like this:

It is necessary to cut 40 threads of 3.5 m each from the cord. Attach them to the top ring.
Using patterns for macrame, weave an openwork mesh.
Insert 8 rings along the bottom edge, braiding them with a thread.
Also braid all the vertical tubes of the frame.
Decorate the bottom edge with decorative elements.

Before you make lampshades with your own hands, you can watch master classes. They will help you master the basic elements of macrame weaving and avoid mistakes in the workflow.

Option number 6: fabric

A fabric lampshade will also look great. With the help of fabric, you can update or restore an old product. It is enough just to cover it with prepared material and decorate it with any suitable decor elements. A fabric lampshade based on cardboard is suitable for a table lamp, wall lamp, infrared lamp, night light and even a chandelier.

To make the product neat, it is necessary, before being fitted, sheathed on a sewing machine. In addition to it, you need to prepare:

iron;
pencil;
ruler;
the cloth;
pins;
matching color threads;
thick paper (thin cardboard or whatman paper);
universal glue.

The workflow consists of several steps:

Make a template of the desired shape out of paper. It is important that it fits the frame.
Connect the template to the fabric using pins. Circle it with a pencil. Draw another line 2 cm from the template line.
Wrap the allowances inward, gradually detaching the pins. Mark the fold line with them.
Remove template.
Sew the fabric on the machine.
Iron the fabric well.
In a well-ventilated area, lay out the workpiece and grease it with glue. Let dry a little.
Glue the fabric to the frame. All seams and cuts must be hidden.
Let the lampshade dry. You can use it after a day.

A fabric lampshade, decorated, for example, with flowers, buttons, bows, will look good. Instead of regular fabric, you can use organza.

Option number 7: tree

Separately, it is worth mentioning the lampshade in the steam room, sauna or bath with your own hands, because there is high humidity, and the glue may no longer hold the shape of the product. For making with your own hands from improvised materials, wooden materials are most popular.

To make a wooden lampshade for a steam room with your own hands, you need to take:

paper;
pencil;
wood;
sandpaper for grinding;
self-tapping screws.

With this set of tools and materials, you can make a corner lampshade:

On paper, draw a template for the bottom of the frame. It should be in the shape of a trapezoid. It is important that its sides fit the walls of the bath.
Using a pencil, transfer the drawing to the prepared wood. Cut out.
Sand with sandpaper.
Cut out 3 strips with a width of 1 cm and a thickness of 0.5 cm. The height should be equal to the height of the lamp.
These strips will connect the top and bottom of the frame. They need to be nailed on the sides and in the center.
After measuring the distance from the center to the edges, cut a few more strips of the same size.
Fasten the strips with self-tapping screws from the inside of the lamp. You can fix them in any position.

As you can see, there are many options for making lampshades with your own hands. In addition to those listed, there are also products made of wire, knitted, lampshade made of beads and many others. In the process of work, almost any material that is at hand is used. If necessary, you can make a new product, or you can update the old one (do restoration). Almost always, a scheme or template is required to work. It is important that the workpiece exactly matches them. Only in this case, the finished product will become a real decoration of a house or apartment.

It happens that you really want to update the interior, but you don’t know where to start. Sometimes you just need to change the lighting. But buying a new lamp is expensive, and in some cases it is not even required. We invite you to consider a few master classes on how to update a table lampshade

What you need to create lampshades

You can update lampshades for your own hands with absolutely any materials:

fabric;
artificial flowers;
skin;
thread and rope;
paper and so on.

It is also a must to have tools such as scissors and a glue gun.

A simple and original way to decorate an old lamp

Such lamps are very well suited for a feminine interior in a chic style. To give the lampshade this look, take the following materials:

shade;
artificial flowers (flower stalks can be bought at craft stores, but you can buy bouquets and cut off hats from them, sometimes it turns out cheaper);
glue gun;
scissors.

Master class on how to update the lampshade for a table lamp with your own hands:

Cut off the excess parts of the stem from the flowers, leaving only the cup that connects the petals.
Heat up the glue gun.
Apply some hot glue to the cup of one flower spike and stick it to the lampshade. Start working from the top or bottom edge. Glue flowers either in a circle or in rows, pressing them tightly against each other.
Hot glue dries quickly, so work carefully.
When you have glued the entire lampshade, fluff the flower petals.

Tip: interesting do-it-yourself lampshades for table lamps are obtained by combining several shades of colors that flow smoothly.

Geographic lampshade

Such a lamp will look great both in the living room and in the child's room.

You will need:

shade;
map;
ribbon;
PVA glue;
some water;
tassel;
glue gun.

Master class on how to make geographical lampshades for table lamps with your own hands:

Prepare a map. You can buy it in a store, print it, or it can be special sheets for decoupage.
Mark the required width on the map and cut out the rectangle. If you do not have enough to completely wrap around the lampshade, then add another piece.
Dilute in a small amount of water.
Cover the back of the card with glue and carefully stick it to the lampshade. Use your fingers to smooth out any bumps, if any.
Wait for the card to dry completely.
Cut off the excess paper.
Heat up and use it to glue the tape along the edge of the lampshade at the top and bottom.

The geographical lampshade is ready!

Book sheets as decor

In the same way, as in the previous mater-class, you can decorate lampshades for using book pages.

To do this, tear out a few pages from an old book and trim their edges so that they are not frayed. Lubricate each sheet with PVA glue and glue it on the lampshade in a chaotic manner. The paper should stick out a little at the edges. When all sheets are glued, tuck the protruding edges inward.

Warm lampshade with ombre effect

Such a lamp is ideal for the cold season, as it will bring a note of warmth and comfort to any interior.

List of what you need:

shade;
several types of yarn that match each other in color palette (for example, white, dark blue and turquoise);
glue gun.

A master class on how to make a beautiful lampshade for a table lamp with your own hands:

Place a small bead of glue just above the base of the lampshade (about one centimeter from the edge).
Glue one end of the yarn to the drop. Choose the one with a darker shade.
Wrap the lampshade with yarn, making sure that each new row fits snugly against the previous one.
Wind a certain height with one color. The last turns should not fit snugly against each other, but be at different distances, cover the lampshade a little randomly (picture 1).
Glue a yarn of a different shade with a glue gun. The new color should be at the level of the old one (picture 2).
Wrap the yarn around the lampshade, and you will end up with two colors intersecting in some rows. This is necessary so that the shades have a smooth transition and do not come out with a striped pattern.
When you have wound the required level of yarn of the second color, make a few loose turns (picture 3).
Wind the third color of yarn, remembering to glue the tip.
Finish wrapping the lampshade. To do this, the third yarn should go in tight rows to the edge of the lampshade, and glue the end (picture 4).
Turn the lampshade over and wind the yarn to the end.

The warm lampshade is ready!

Lampshade with roses

You will need to take the following tools and materials:

shade;
cardboard;
pieces of fabric;
green yarn;
ribbon;
glue gun;
scissors;
pencil.

A master class on how to decorate a lampshade for a table lamp with your own hands (a photo of the process is attached):

Draw flower leaves on cardboard, and then cut them out (picture 1).
Glue green yarn to the edge with a glue gun (picture 2).
Wrap the yarn tightly around the leaf (picture 3).
Glue the tip of the thread and make a few more leaves in the same way (picture 4).
Cut a few strips from the fabric about one to two centimeters thick (picture 4).
Fold one strip in half, dropping a little glue inside along the entire length (picture 5).
Twist the strip tightly, sometimes dripping glue on the edge to keep it from coming apart (pictures 6 and 7).
Straighten the edges of the figure a little, and you will get a rose (picture 8).
Make several roses in the same way, different in size.
Carefully glue the roses on the lampshade (picture 9).
Do not forget to glue the leaves under the roses in some places.

Volumetric lampshade is ready!

New lampshade with ombre effect

To make a smooth and beautiful transition from one color to another, you need a suitable coating. To do this, it is recommended to make a lampshade with your own hands.
You will need:

lampshade frame;
cotton plain fabric (preferably white, beige or light gray);
small bath or basin;
paint (watercolor, for hair, for fabric, gouache and any other liquid);
glue gun.

A master class on how to make a lampshade for a table lamp with your own hands with an ombre effect:

Take the lampshade frame and fabric.
Turn on the glue gun.
Wrap fabric around the lampshade and carefully glue the edges together. Cut off the excess fabric.
Wrap the top and bottom edges inside the lampshade and glue them with a glue gun.
Fill a bowl or bath halfway with water and dilute the paint in it.
Lower the lampshade not completely into the bath and pull it out.
Do this procedure several times, gradually reducing the dipping height. Thus, the paint will be more absorbed at different levels, creating a smooth transition of shades of the same color.
Hang the lampshade in the bathroom and let it dry.

All is ready!

How to make a lampshade from scratch

The previous master class told how to update a boring or outdated lampshade. And what to do if there is nothing to work with and there is not even a frame? Then you can easily make a lampshade with your own hands.

For this you need to take:

the cloth;
masking tape;
large ruler and centimeter;
pencil;
scissors;
plastic sheet (can be found in hardware stores or among needlework supplies);
wire rings;
large clips-clothespins;
PVA glue or;
glue gun;
special splitter for lamps (sold in lighting stores).

Operating procedure

A master class on how to make a new lampshade for a table lamp with your own hands:

Take a tape measure and measure the diameter of your wire rings. This will be the diameter of the lampshade.
Put a plastic sheet on the table and measure the length and width of the future lampshade on it
Cut out the marked rectangle.
Turn the fabric inside out on the table.
Pin the edges of the fabric so it doesn't move.
Cover the plastic rectangle with a layer of PVA glue or double-sided tape.
Gently place the rectangle with the sticky side on the fabric.
Press the fabric against the sheet and smooth it out.
Cut off excess fabric.
Roll the canvas.
Glue the canvas with a glue gun.
Connect the seam with clothespins and place the part on the table.
Put a weight on top of the seam so that it does not stick out.
Wait for the part to dry.
Place inside the parts from above and below along the ring.
Attach a special splitter to the upper ring.
Glue the rings with a glue gun.
Attach paper clips to the edges so that the rings stick better. Leave it like that for a while.
Glue a ribbon to the top and bottom of the lampshade, wrap half of it inward.
Cut a strip of fabric, fold the edges over and glue to the seam.
Cut two more strips of fabric, also turn the edges and glue them to the top and bottom of the lampshade.
Wait until all items are dry.

A brand new lampshade is ready!

Each person tries to decorate his home as comfortable as possible, using modern design solutions. A lampshade turns a room with poor and depressing light into a cozy place, but choosing the option that suits the design and wishes is troublesome. It is often difficult to find what you need, and if you can, then for an unreasonably high price. At this moment, any creative housewife will say: “I will sew it myself!” For the possibility of embodying all creative ideas, we will consider how to sew or glue any suitable product.

One of the most popular subjects of needlework is the decoration of lighting fixtures. Everyone wants a bright light to break through an unusual lamp shade, made in combination with the overall design of the room. And it can be not only a chandelier - all kinds of wall and table lamps will give your home comfort and beauty. How to make a lampshade with your own hands? After spending a little time, you can make a unique decor element for the chandelier and its frame from improvised means.

What materials can be used?

Suitable raw materials can be absolutely anything. The chosen material largely depends on the experience of the person in needlework, as well as the availability at the moment, its cost and compliance with the overall interior of the room.

Can be used:

paper, cardboard;
the cloth;
plastic;
threads;
metal (frame for lampshade);
finished products - bottles, spoons, forks.

The material for the chandelier is limited only by your imagination and what a person can do with his own hands. You can practice for a start on cheap and affordable materials - white paper or cardboard; use old fabric (if there is a lot of it). After you understand what and where you need to fasten, you can move on to more expensive and rare materials for your sconce.

What will we need?

In addition to the raw materials themselves, you also need tools to fix and shape the finished product:

needles, scissors, pins;
glue;
pliers (for metal frames);
wire (base for lampshade);
soldering iron.

Keep in mind that the finished product must have a weight that will easily be held on the selected mount, and be safe enough when light bulbs are working next to it.

Paper products

One of the easiest options is to use stiff wire to create a spherical frame on which you can stick any color of paper on top. There will be enough space for the light bulb, the lamp will look both simple and stylish at the same time. Usually this is how you can make a lampshade for a floor lamp with your own hands.

In addition to the spherical shape, you can prepare the frame of a cylinder, rectangle or square, as well as an elementary cone. A simple master class - take several wires of different lengths, bend them into a circle and secure with a soft piece. Having made about 15 of these rings, you will get an excellent frame for the lamp - what a chandelier requires.

Any patterns can be cut out on the surface of glued paper, cardboard with scissors or a clerical knife. It can be geometric shapes, animal drawings, letters, snowflakes, leaves - anything that fits into the interior of the room and helps to update the lampshade. Do not rush to throw out the cut out parts - they can be glued to a long thread, and the thread itself can be attached to the frame. Thus, we get beautifully hanging patterns, the chandelier will turn out to be very unusual, the decoration will be definitely unique. Such a handmade chandelier lampshade will look good in a nursery.

Cut patterns on the threads

Cut soft paper or fabric into long strips with different ends, which are attached to a round rigid wire frame. Don't make the structure too dense if you plan to use a powerful bulb for your sconce - too much heat can cause it to break or even catch fire. This is an ideal way for low-power evening lights in the hallway, decorate them also in the summer kitchen or in the hallway.

Fabric Options

Here, much more potential is already opening up due to the characteristics that different materials have. This is both density and pattern, and the ability to create very complex shapes by gluing and stitching all kinds of elements; we decorate with literally anything, this is a good way to make a lampshade for your favorite floor lamp.

A fabric lampshade adds cosiness and warmth to lighting fixtures in kitchens, children's rooms, living rooms, and bedrooms. The soft light that breaks through such products is more intended for additional lighting (for example, sconces).

A strong frame made of rigid wire is mandatory, which must withstand sufficient weight in the case of using dense types of fabric.

Is it possible to independently update existing lampshades or chandelier shades? Do not get hung up on one fabric, pattern or color - with the help of glue and threads on the surface of any lampshade, you can attach a large number of various elements that correspond to the idea of \u200b\u200bthe interior. It can be multi-colored stripes, patterns, edging and dividers, bows and ruffles - everything from which a lampshade can be sewn. And if earlier a seamstress sewed ruffles with a base with a hidden seam, a modern original decor element can also be sewn with an open seam with a bright silk thread in contrast to the main color, it can be decorated with anything on top.

Fabric is a strong enough material that can withstand glued bead and plastic items, even glass jewelry will look very good in this case. A great option for making a table lamp shade.

How to make a lampshade for a table lamp? On a white fabric, you can write a poem or an excerpt from your favorite book in beautiful handwriting so that the light, penetrating through a beautiful lampshade, reminds you of a good work. Ideal for updating your bra.

Thread or very thin strips of fabric

Wrap the finished wire frame (or you can use any other voluminous object, for example, a five-liter plastic bottle) in several layers with a thick thread or strip of fabric. Such lampshades look very good in kitchens or dining rooms, hanging over a dining table or bar.

A ball of thread impregnated with glue

Using thread to create the surface of the ceiling

On the surface of the finished ceiling, you can stick different figures and patterns by analogy with paper options, creating a wonderful table lamp for reading.

Plafond of threads or plastic wire with figures

An interesting option for creating a spherical shape is to use a regular balloon. The final shape of the lampshade depends on the shape of the inflated balloon.

Plastic products

Let's move on to the most difficult options. You'll have to be patient, material and glue. It is rather difficult to obtain products with smooth bends from hard plastic, therefore, in most cases, a strict product is made. It is also possible to arrange from various parts of different shapes and colors, a soldering iron or glue is used for fastening.

How to make a plafond? From plastic, you can assemble lampshades of cubic, conical shapes, as well as fasten various parts together and get a very complex and practical product that will find application in absolutely any room.

How to make a frame for a lampshade? If you glue a plastic five-liter bottle with various details, you will get amazing lampshades in the form of fish scales or exotic fruits. Using multi-colored varnish or spray paint, you can paint the finished product as you like. Not suitable for a sconce, because it has a rather large size in the end.

Beads

Instead of threads and wire, finished frames can be wrapped with beads or glass beads can be used. So you can make a lampshade for a table lamp with your own hands. It turns out a multi-colored surface, which, under powerful lighting, beautifully plays with colors and shimmers with gloss, creating glare on the walls and ceiling of the room. Due to the frequent compactness, a beaded lampshade is well suited for table sconces.

Conclusion

To create lampshades with your own hands, you can use absolutely any material. The variety of colors and shapes that are available from scrap items will allow you to move away from the relatively limited range of modern stores. A homemade lampshade will definitely please your guests. This is an ideal option - for any lamp, create a lampshade with your own hands, which will very accurately fit the interior of your home. Sew anything from anything, apply alterations to all the designs that are already there.

The decor of the table lamp can be made of both plastic and paper. It is better to use light materials for bright light. Making beautiful lampshades with your own hands is a simple matter even for those who have never done it.

When bad weather rages outside the windows or on a long winter evening, or perhaps just in moments of solitude, you want to sit in a soft comfortable armchair with your favorite book, drink a cup of sweet tea with a pleasant companion or arrange a romantic date with your lover. At such moments, a familiar and homely interior element such as a floor lamp, a chandelier or a lamp, but always with a beautiful lampshade, will come in handy.

As a rule, floor options are located near armchairs, a bed or a soft sofa, and a lamp with a beautiful lampshade can be located above the dining table or in the bedroom.

The lampshade is quite simple to make with your own hands, while you can be proud of its exclusivity, originality and style. Interiors with lampshades fill the atmosphere of the room with sensuality and romance, create comfort and attractiveness.

The lampshade is easy to make from any available materials, textiles, paper and decorative things (beads, rhinestones, ribbons, etc.) are quite suitable for this.

You can improve or modernize an old lampshade using the power of your imagination and diligence. At the same time, the interior design will be filled with individualism and become truly homely. We recommend that you consider a variety of options for using the lampshade in our photos.

Frame and base preparation

First you need to decide for which lamps you need to make or update the lampshade. If for the old one, then the frame should be removed and freed from unnecessary parts, if it is missing, then you should buy it ready-made in a building supermarket.

It is easy to make it yourself, with pliers and wire on hand. Frame configuration may vary. It is most convenient to make a lampshade for the base in the form of a cylinder or cone.

The choice of fabric for the lampshade

For the future product, you can use fabrics of different textures: light, hard or dense. Even wool is suitable, the main thing is the harmony of the combination with the entire interior solution as a whole. For example, a table-top version of a lampshade for a lamp is suitable for a classic bedroom, i.e. small size and white color matching the style.

A frame made of ordinary wire is best hidden behind an opaque material. For example, cotton, taffeta or dark silk.

An important point is the choice of fabric color, as it can be warm (yellow, orange, red, etc.) or cold (blue, green, etc.).

Auxiliary materials

Fabric lampshades can be created in a variety of ways. For example, a new lampshade, which is fixed to the old one, does not require any preparation for the main process. A hand-made frame requires coating with paint and wrapping with a cotton tape.

An iron, a pencil, a ruler, fabric, pins, threads to match the fabric, strong paper, universal glue - this is what you may need when working.

How to make a lampshade with your own hands using fabric

To make a lampshade with your own hands, they mainly use: linen, silk, denim and other fabrics.

In the production process, a whole cut or material cut into strips is useful. Their width can be different. The prepared frame can be easily covered with a plain fabric with a pattern.

However, it is necessary to immediately decide on the future location of the lampshade, because it must match its surroundings, and not stand out as a white crow.

Design professionals recommend using the frame of the old one to create a new lampshade model for a floor lamp. Although it is not at all difficult to build it with your own hands from hard wire. Use light bulbs that save energy to avoid fires.

To create a masterpiece hanging lampshade on your own, you need:

Prepare the frame of the future product (use the design of the old lamp or do it yourself).
Choose a suitable fabric, cut into even strips about 5 cm wide, in the amount of 25 pcs.
Check the evenness of the edges of the strips.
It is good to iron them with an iron.
Wrap the ring on top with the edge of the tape and fix (sew).
Take the tape down and wrap its edge around the ring at the bottom, then go back and wrap the top around.
Wrap the rings until the tape ends, then fasten its edge.
Take the next strip and continue wrapping.
When the frame is completely covered with ribbons, you need to prepare the belts for the edges.
Take two small pieces of fabric of a different color and cut out 2 strips of a certain size, iron them, bending along the edge of the tape 2.5 cm inward.
Fold the strip in half.
Stick double-sided tape on the frame rings, and a fabric strip on top of it, making light cuts along the edge so that it lies as evenly as possible.
Bend the other edge inside the base and also stick adhesive tape.
Decorate the upper and lower tiers of the frame with belts.

For edging, you can use crocheted ribbons or well-known ruffles.

Use of textile and plastic materials for the lampshade

This manufacturing option is made of textile and plastic material to update a worn product or improve a new one:

we measure the diameters of the rings at the top and bottom, the height of the frame base, adding 2 cm to them to each edge for seams,
we take a thin plastic plate of a rectangular or trapezoidal shape, cut off the excess to the desired size, and use it as a base for a fabric lampshade,
we cut the fabric in accordance with the required parameters and fix it to the table surface with double-sided tape,
glue the fabric to the plastic,
with the resulting element we bend around the base and fix the edges with clamps,
mark the place of the seams on the fabric,
remove the paper clips and strengthen according to the basting with glue, press and leave to dry,
glue the lampshade from the inside,
glue the place of joining of the rings with the frame,
if the product is dry, the clamps are removed,
fasten paper tapes at the top and bottom so that one edge is below the location of the rim of the ring,
fold the free edge inward and fix it with glue,
we take a fabric strip of a different color with a length equal to the height of the frame, and a width of 5 cm, bend it in two, bend the edges and iron it,
we coat the inside of the tape with glue and fix it,
fix the strip with glue over the seam of the lampshade,
prepare paper ribbons 5 cm wide,
glue to the upper and lower edges of the lampshade, fasten with clips,
Glue a fabric strip on top of the paper.