Cover the old door with plaster. How to decorate the entrance and interior doors, materials and methods of exterior and interior decoration. Useful tips: how to update an interior door with your own hands

03.09.2016 61396

Samples probably still remain in the apartments and country houses. Their appearance leaves much to be desired, but the owner of the home simply may not have the money to replace the old structure with a new one. In this case, you should not refuse repairs, because it is always possible to update old doors. From our article, readers will be able to learn how to update an old one, giving it a beautiful and modern look, and without spending large quantity funds.

Preparing the door surface for renovation

Make beautiful old door within the power of any person. This procedure requires only a little patience and labor. The first stage of work consists of preliminary preparations for restoration.

So that in the process of repairing the old door design You don’t have to waste your energy on trifles; think about preparing the surface in advance. To update you will need the following materials:

• Acrylic paint;
• Sandpaper (for sanding wooden surface);
• Putty;
• Acrylic varnish;
• The film is self-adhesive.

So, new finishing of old doors begins with preparing the wooden surface. The main advantage of the work being performed is that all the actions are done with your own hands, which means that you do not need to pay for the services of craftsmen, who are not cheap. Preparatory stage Before starting the restoration of the old door structure, the following is performed sequentially:

• First, remove it and place it on a clean and level surface. Immediately try to remove all fittings and glazing beads so that nothing interferes with you during preparation.
• Before installing new ones, remove the old coating first. For these purposes, the thermal method is best suited, which involves heating the painted surface with hot air produced by a hair dryer. When exposed to dry and hot air, the paint on a wooden surface begins to bubble and peel. Now it can be easily removed with a spatula.

Advice. If the paint is old or applied in several layers, then it is unlikely to be removed in one go. After removing the base paint with a spatula, heat the surface again door leaf in those places where peeling of the paint and varnish composition has not occurred. After this, take the spatula again and remove the remaining paint. If the composition remains in the recesses and grooves of the door, remove it from there with a triangular spatula or the sharp corner of a regular spatula.

• The paint is completely cleaned, and now, armed with sandpaper, sand the old wooden door thoroughly. To make the plane even and make it more convenient to work, secure first sandpaper on a flat rectangular block of wood.
• To improve the quality of sanding, use coarse-grit sandpaper at the very beginning, then medium-grit material, and finally fine-grain paper (to polish the sanded surface).

It should be remembered that the polished and sanded surface of the door leaf cannot be immediately coated with a new layer of paint. The fact is that there may be cracks and small scratches on it, which should first be removed with putty.

• Buy at retail network wood putty is not difficult. By the way, you can make it yourself. For this purpose, simply mix the small sawdust with PVA glue.
• Fill all the unevenness on the old door with the prepared putty composition using a spatula.
• After puttying, let the compound dry, and then sand the door leaf with sandpaper in accordance with the scheme described above. As a result, you should have a perfectly flat and smooth surface.
• Last stage preparatory work– applying a layer of drying oil. Its shade may be slightly darker than the color of the wood. Drying oil will become a reliable basis for further application of paints and varnishes.

Options for restoring old doors

Having decided to update appearance old door, be prepared to choose the best way restoration. This procedure can be performed in several ways, using various materials.

Coloring

You can turn an old door into a new one by painting it. This option is used most often, and its essence is to apply a paint and varnish composition to the door leaf. Usually, to do this type of work with your own hands, you use a roller or spray gun. The brush is used only for good painting hard to reach places. When choosing a roller, we recommend giving preference to pile models, since foam rollers wear out very quickly.

Veneer finishing

Finishing old doors with veneer is a longer and more labor-intensive process compared to the technology of wallpapering or painting. Finishing work using veneer are carried out in the following sequence:

• Prepare the web in accordance with the technology described above;
• Now prepare mock-ups of the veneer parts using tracing paper or old newspapers for this purpose;
• Carefully try on all prepared elements, applying them to the surface of the door;
• transfer paper models onto veneer, and then cut out parts from it to decorate old wooden doors;
• Try the veneer elements on a wooden plane, then apply a thin layer of glue to the surface of the door and the veneer part;
• Attach the cut out part to the canvas, aligning the glue-coated surfaces, and press firmly. Smooth the plane starting from the middle of the part, moving towards the edges. We recommend using a slightly heated iron for this purpose;
• To extend the service life of this decorative covering, coat the top of the veneer with wax.

Pasting with wallpaper or vinyl

If the old door has glass elements, they can be replaced with plywood inserts, making the entire structure solid and opaque.

To use wallpaper or vinyl, follow this sequential pattern:

1. To secure decorative elements, use PVA glue. It is better to prepare the adhesive composition in advance. If you choose wallpaper to decorate an old door leaf, then it is better to give preference to washable models. They are easy to care for and get dirty less often. Such material will significantly extend the service life of the door plane.
2. Cover the surface of the canvas with a layer of glue prepared in advance, and then press it firmly against it decorative element. Just try the wallpaper dry first to accurately measure some of the material.
3. When pressing the wallpaper onto the glue-treated surface, try to thoroughly smooth the material, removing all the air from under it. This approach will eliminate the possibility of bubbles forming on the decorative surface.

Features of restoring modern hardboard doors

The repair of doors made from modern material hardboard For this procedure, you will need to purchase self-adhesive film. The doors themselves are also removed from their hinges and carefully inspected before the restoration begins. Before filling cracks, be sure to degrease the surface. Only after completing this procedure can you apply varnish or coloring composition on a hardboard canvas.

I would like to pay special attention to the self-adhesive film. It happens different quality, with varying degrees of transparency. Naturally, more expensive material will be better.

Cut the purchased film to the size of the door leaf, and then carefully stick the material along the entire perimeter of the restored door structure. It is recommended to smooth the already pasted material with a towel to prevent the appearance of bubbles and ensure uniform fixation over the entire surface. Smooth the self-adhesive film from the middle to the edges. If it happens that bubbles still appear on the surface of the pasted film, they can be easily removed with a needle. A door leaf covered with such a film material will have an impeccable and beautiful appearance. After securing it, the door can be installed and the fittings can be secured to it.

Now you know that a new door leaf can be made from old ones. This will make it possible to modernize the interior of the house, but also save on repairs, purchase and installation of a new door.

If you want to update your interior while spending a minimum amount of money, then great solution There will be door decor with your own hands. There are many ways to freshen up your home. Let's look at the most interesting and accessible of them.

Decor interior doors

Glass door decor

Beautiful door decor

One of the easiest ways to decorate interior doors with your own hands is to wallpaper. Wallpaper - universal material, which can be used for different types finishing Don’t think that after updating the door will seem old-fashioned. The main thing is to do everything carefully and choose a good combination of colors. The following types can be used for decoration:

• scraps of old wallpaper;
• plain bright materials;
• wallpaper with a pattern or ornament;
• photo wallpaper.

One of the most quick options– photo wallpaper for doors. Decorating with this material can be done quickly and accurately. In addition, there is an opportunity to show your imagination, spend a little more of your time and become the owner of a unique result. So, how to decorate a door with your own hands using wallpaper? The work includes several steps.

Operating procedure

Door decor with drawings

Dye

Another simple way to update your interior is to paint the door. This method design has several important advantages.

• Affordable price.
• Durability.
• Possibility to hide stains.
• Lots of room for imagination.
• Ease of use.

Decor of interior doors

Decor of wooden doors

Beautiful door decor

Decorating with paint includes several stages.

• Remove the door from its hinges, lay it horizontally (it is better to take it out of the living room) and clean off the layer of old coating. This step is very important, since paint, unlike other decorative methods, does not hide uneven surfaces.
• Clean with sandpaper.
• Level with putty, dry, degrease the surface.
• It is better to paint not the entire surface at once, but in small squares, starting from the top. Each area should be painted evenly. If the plans include drawing a picture, then in any case, the first place should be a smooth background of the canvas. To avoid smudges, it is better to lay the door horizontally.
• After the paint has dried, the door must be varnished and dried again.
• The last step is to install the door in place.

When buying paint, it is better to choose acrylic paints; they apply in an even layer. It is not necessary to use brushes; a spray bottle will allow you to evenly and quickly change the color of the surface.

Door decor with drawings

Decorating doors with different shades

Additional decor

There are several other ways to add uniqueness to your door design.

• Craquelure varnish. If you apply it to a painted door leaf, small original cracks will appear on it.
• If available, moldings can be painted in a contrasting color. They are also easy to make with your own hands and decorate the door.
• Painting. This decoration will take a lot of time, but the result will be pleasing. For painting, minimal artistic abilities and limitless imagination are enough. You can draw anything: ornaments, flowers, ornate patterns, landscapes.
• The stencil is suitable for those who do not know how or are afraid to draw by hand. You can buy them in specialized stores or make them yourself from cardboard.

Stained glass

Stained glass is perfect for doors with glass. The result, as a rule, looks original and impressive. Acrylic or special may be suitable stained glass paint. You can actually buy them in art stores. More often they are sold in whole sets with detailed instructions.

You can apply absolutely any design to glass. In addition to paints, you will also need an outline. It is he who creates “metallic” boundaries between the painted pieces of colored glass.

When working, it is better to carefully remove the glass from the door to avoid smudges and accidental drops falling on the wood itself.

Glass door decor

Beautiful door decor

Actions are performed in the following sequence.

1. The glass is cleaned of dust and dirt and degreased.
2. Transfer from a printed drawing or apply a contour “by hand”. It must dry well, this can take up to three days. Most likely, you will need to reapply the contour to make it look more voluminous.
3. Color the separated pieces different colors, let dry.

Decoupage

An original and creative way to decorate doors with your own hands. Moreover, you can use it to decorate absolutely any surface. Works especially well on quality wood. A vintage style back in fashion.

Before applying pictures, the door must be treated with a primer or acrylic paint (if you need to level it, putty will do). After this, the creative process can begin.

For decoupage, special napkins (available in craft stores), wallpaper or fabric are usually used. In addition you will need:

• scissors;
• PVA glue;
• brushes, sponges, rollers.

First, the elements are applied to the surface, the exact location is noted, and the different options. Glue them using PVA (replacing glue is not recommended). You need to glue the picture from the center, smoothing out the bubbles and folds.

Door decor with drawings

Decorating doors with different shades

After drying, be sure to coat the surface with varnish.

Many people use it for decoupage various photos. The technique remains the same; it is enough to simply separate the bottom layer of paper from the photo so that the gluing is reliable. You will have to do the same with the wallpaper.

Textile

Another one of original ways door decoration - patchwork technique. It’s worth noting that not just any fabric will work. The choice largely depends on the room for which the door is intended. Fabric decoration is more suitable for bedrooms or living rooms, but very impractical for the bathroom, toilet, front door.

Using the patchwork technique, you can create a unique piece of furniture with your own hands. Special attention you will have to pay attention to the choice of materials:

• when choosing fabric, you must take into account that it can shrink or stretch (it is better to take measurements with a damp cloth if glue will be used);
• When drying, the glue should not leave any traces;
• the edges of all flaps must be processed;
• near door handles It is recommended to use non-stainable types of fabric.

It is not necessary to use glue to work. With glazing beads or furniture stapler decorating will go even faster. A stronger fabric (tapestry) will be more reliable for the door leaf.

Decor of interior doors with a pattern

Decor of wooden doors

Beautiful door decor

Stickers

Quite simple and quick way decorating doors with your own hands - using vinyl stickers. It is perfect if the door is in good condition, but is simply tired and the owners want to add variety to the interior, decorate something. You can combine stickers and wallpaper.

Ready-made stickers can be selected at any repair store or ordered on specialized websites on the Internet. If you want to add even more originality, you can order stickers based on photos. For example, a door decorated with a collage of photos of all family members will look original.

Door decor with drawings

Decorating doors with different shades

You can also create them yourself. For this you will need:

• scissors;
• PVC film;
• cardboard.

The desired design is carefully transferred to cardboard, then its contours are cut out from self-adhesive film. The unique sticker is ready.

If there is any defect on the door leaf, you can buy stickers.

The option with stickers is more suitable for bathrooms than interior doors, as it perfectly repels moisture.

Decor of interior doors

Decor of wooden doors

Beautiful door decor

Mirror

Installation of a mirror on the door surface - original and quick method updates. It will help hide many defects of an old piece of furniture. The mirror will look best on the front door, since the hallway must have a reflective surface.

Door decor with drawings

Decorating doors with different shades

Mosaic

One of the most unusual options decoration - mosaic. It is used quite rarely, since not all doors can withstand a layer of ceramic coating. The thickness of the door leaf itself increases significantly, its quality suffers, but the result looks incredibly beautiful.

Video: Door decoration

50 photos of interior door decor ideas:

Do not rush to dismantle the boring old interior doors and replace them with new ones. Consider updating them, there are many ways to decorate and restore them. old furniture, applicable to door leaves.

Decorating doors made of fiberboard

Process step by step:

1. If the door is completely askew, you must first remove it from its hinges and remove the old fittings. New handles, locks, latches in the same style on all interior doors will be the first step towards updating them.
2. So the door was removed. Now you need to delete old paint. Use a heat gun and a spatula.
3. After this, the cracks and scratches are sealed using special putties and putty.
4. Wait until the surface dries and sand it.
5. Cover the canvas with drying oil, which will prevent it from deforming under the influence of moisture.

See the video for a visual demonstration:

The door is ready for actual decoration. The easiest way is to cover the door leaf with colored paint or varnish it. Next, there is room for imagination:

• make a drawing using a stencil;
• paint the moldings a different color;
• stick on moldings if they were not there or imitate them with paint.

A variety of applications - fabric, paper, vinyl, leather, photo wallpaper - will allow you to turn an old door into a new one - original, stylish and unusual.

Decorating an old bathroom door

Before you start decorating the bathroom door, you need to consider important point. Since there is always high humidity in the room, the coating that you apply to the door, or more precisely, to inner side, must be resistant to this factor.

How to prepare the door leaf is described in the previous section of the article. In short: the door needs to be removed old layer paint, sand, putty and prime the surface. If strips are missing, you can buy them and attach them to the door. After painting everything in one color, you get a complete picture.

An excellent option for a bathroom door is to install a full-length mirror in a frame made of slats. If it is flexible and plastic, the installation process will be quite simple, but the effect will exceed expectations: it is beautiful, practical, and useful.

The mirror can be replaced with a mosaic, a special vinyl sticker, and even a piece of wallpaper (only washable and moisture-resistant). By experimenting with materials and colors, you can make an old bathroom door look stylish and special.

How to decorate old doors with glass

The first option that comes to mind when thinking about decorating options for an old door with glass is stained glass. What you will need for this:

• water-based stained glass paints;
• black paint - for the outline;
• sketch of the image.

Transfer the drawing to the glass, outline the contours with a thin black line, and after drying, begin decorating the elements with different colors.

You can make your work even easier by simply purchasing a special film that imitates a stained glass picture.

One of the options for decorating a door with glass in the video:

Stained glass windows allow you to make even an old door unusual and stylish

If the old glass in the door was transparent, it can be made frosted. To do this you will need to purchase liquid glass(1 liter will be enough, its price does not exceed the cost of a chocolate bar or a cup of cappuccino), which will need to be mixed with crushed chalk (or tooth powder). The resulting paste is applied to the fat-free, flat surface in 2 layers.

An easier way is to stick a special film or buy a ready-made matting paste.

Choose your option for decorating old doors, and you will see how easy it is to update the decor in your apartment with your own hands and without extra costs.

After renovating a room, the owners may be faced with the fact that the old interior door does not match the new interior, although its functionality may still last for some time. In this case, you should think about how to update the interior door with your own hands. There are several decorative techniques that vary in complexity and cost of materials. All you have to do is choose the most suitable one.

Preparatory work

Before decorating interior doors, they are prepared. The following tools are used for this:

• construction adhesive;
• tracing paper;
• press.

The door needs to be removed. Then examine the canvas for defects. If the old box has scratches, they need to be repaired with wood putty. You can decorate the canvas with photo wallpaper. If the doors are peeling in some places, then an adhesive mixture is applied, tracing paper is applied, and pressed. An adhesive mixture is also used to seal cracks and microcracks. If the defects are large, adhesive composition chips with fine dispersion are added.

Door Upgrade Methods

TO simple ways canvas updates include:

• applying varnish;
• coloring;
• use of stain and veneer;
• stained glass

Painting, varnishing and staining

Old wooden doors can be updated by painting, varnishing and staining.

Water-based, synthetic and organic dyes are used. After this, the door takes on a neat appearance.

The door leaf is possible. Wood varnish is well absorbed into the wood, evenly covering the entire surface of the structure. The main advantage of the protective and decorative composition is the presence of a tint base.
To apply the varnish, use a sprayer or brushes. Experts advise decorating the wood with a brush, which easily follows the structure of the structure, well saturating hard-to-reach areas. To increase protective properties, it is recommended to paint the door in 2 layers.

If you need to refresh the box in once again, stain is used. Then the coating is treated with varnish. Stain can be used to update color range canvases. It prevents the mixing of tones, and subsequent varnishing enhances the brightness of the color. Sanding gives it a matte finish.

If there is no need to create a matte surface, polishing and drying are carried out after grinding. This technology gives the door a crystal shine.

Veneering

Veneer is used to decorate the door. This decoration technique wooden canvases applies if they are made from cheap sawdust. Due to veneering, the door acquires an aesthetic appearance. Veneer must be glued transversely to the wood fiber.

Veneer gives the door the noble appearance of real solid wood

Self-adhesive film

You can decorate the box with self-adhesive vinyl that imitates wood. Using this technique, coating defects can be easily hidden. Before gluing a wooden door, you will need to prepare a hairdryer, fabric, and scissors.

At the first stage, the coating is cleaned of various defects. This stage is considered the most difficult. Next, marking is done using a tape measure. These canvases are transferred to millimeter markings made by the manufacturer on the back side of the film. A knife is used to cut the product.

The film hides everything minor defects and gives the surface the appearance of natural wood

The cut pieces of self-adhesive are applied to the desired area doors. On the reverse side of the film there is a protective layer, under which there is glue. A few centimeters of the layer are carefully peeled off to stick the product on the door.

The overlay, completely applied to the door, is smoothed with a rubber spatula or soft material. Self-adhesive is wrapped on all ends of the covering. Cut the corners right away PVC products, install a lock with a handle.

Photo wallpaper

Using modern photo printing, an image is transferred to paper the right size. Photo wallpaper on wooden doors look beautiful. Any image can be printed. For this you can use the services advertising agency or printing house. The image can be selected at home or with the help of specialists.

One of the options for updating interior doors is photo wallpaper.

On plain wallpaper You can stick polyurethane or foam moldings. In this case, the style in which the doors were decorated will change. The resulting design is suitable for a room decorated in classic style. If you use a colored background or moldings with curves, then the doors will be decorated in Provence style.

Before applying the design, the surface is leveled and treated with glue. If paint comes off the door, remove it. Wallpaper is also treated with glue.

A rubber roller is used to level the canvas. If any bubbles remain, remove them with a plastic spatula. Then the remaining air is removed from the center of the structure to the edges. Using this spatula, smooth the wallpaper joints (if any). If the technology is performed correctly, then the joints are not visible.

Wallpaper with moldings is suitable for interiors in a classic style

The edges of the wallpaper need to be trimmed with a knife. This is done until the wallpaper softens from the glue. Otherwise, they will tear and stretch easily. It must be left to dry for several hours. The process of decorating fiberboard or solid wood continues after 12-24 hours. It depends temperature regime and humidity levels.

A simple pencil is used to apply markings. After the drawing has been applied, you will need to measure the length with a tape measure constituent elements molding. Then they are cut off and the edges are filed at an angle of 45 degrees. Spread with PVA glue back surface pieces. They need to be glued according to the marked markings. When the canvas has dried, it can be installed back. Using this principle, you can update the doors of a bedroom, nursery, or kitchen at home.

Drawings and paintings

The advantages of this decor include:

• beautiful and original appearance;
• simple execution;
• the ability to use ready-made stencils;
• wide choice of materials;
• embodiment of different ideas.

The disadvantage of this method is that its application requires artistic skill..
At the first stage, the coating is degreased with alcohol and treated with a primer. The last composition is applied twice. Applies similarly acrylic paint. Each subsequent layer of paint is applied after the first layer has dried.

When zoning, the shape of the paneled part of the covering and the geometry of the ornament are taken into account. To give the surface a vintage look, the contours of the zones are covered with a different color. The paint can be applied with a sponge. The stripes that protrude on the door can be painted golden color. Then the ornament is transferred to the surface and painted in suitable colors.

Decorating using decoupage technique

Decoupage does not require dismantling the door structure. You just need to wash and dry the coating. The opening is preliminarily covered with mounting tape. The tree is primed well and efficiently. The surface is rubbed with a simple paraffin candle and then painted. The next stage is gluing the decoupage card. It is pre-soaked in water for 12 minutes. The remaining drops of water are wiped off with a rag. The back of the strips and the surface of the door are treated with PVA glue.

To decoupage the door, special decoupage cards are used

Each piece is glued tightly. In this case, you need to make sure that folds and bubbles do not appear. If such defects are not eliminated immediately after they appear, the coating will turn out uneven.. If the coating has dried, putty is applied to the edges of the component elements. Excess composition will need to be removed with a wet rag or sandpaper. A varnished box will require more long preparation for painting. The varnish is first removed and defects are eliminated.

If necessary, the edges of the canvas are processed and abrasions are left. This technology will give the coating a vintage style. If complied with step by step instructions, then ready decorated doors will look original with details different shapes. They can be cut from napkins. The color of the future canvas is selected taking into account the shade of the interior of the entire room. The material is glued using the method described above. Finished coating varnished with an acrylic base.

Antique decoration

An antique wooden door can be seen not only in apartments, but also in houses and offices. At the same time, decor that imitates antiques is rare. It gives the door leaf individuality. Craquelure means applying two layers of varnish to the door. Particular attention is paid to the process of selecting varnish - each layer must have a different composition and different times drying. The coating is first cleaned, degreased and dried.

Craquelure gives the door the appearance of old wood

To age the door, you will need some materials:

• special varnish for craquelure;
• bitumen varnish, which gives an antique effect;
• acrylic paint.

Craquelure varnish is applied to the prepared coating. If the 1st layer is dry, apply the 2nd layer - bitumen varnish. It is needed to enhance contrast when used white background. If applied dark tone, acrylic paint is used. This technology is considered the best. If necessary, craquelure varnish is replaced with simple PVA glue, vinegar, egg white or gelatin. This method of updating doors is suitable for people who like an antique style.

Decor with stencils

If you have mastery in processing wooden products You can use a more complex canvas update. To apply decor with a stencil you will need:

• leather;
• glass or mirror tiles;
• stained glass;
• mat;
• bamboo curtains;
• bars;
• veneer.

Carrying out such decoration requires perseverance and good imagination. In the end it will be possible to do original door, which will fit perfectly into any interior.

Using stencils you can change the door design

The door, the panel of which is replaced by a stained glass window, gives the room unusual look. To implement this idea, water paint is used. The desired pattern is first sketched onto the surface. Paint is used to transfer the design onto the glass coating. This procedure is performed in a certain sequence:

• preparing a sketch of a drawing on paper;
• glass processing by cleaning and degreasing;
• substituting the design on the glass and then tracing it from the back with a thin brush;
• painting the outlines of the drawing with different colors of paints.

After completing the process, the paints must dry within 22 hours. Then the glass fragment is mounted in the door and fixed well.

Updating the opening and slopes

In addition to the door itself, the doorway is also updated. If this is not done, then the canvas will have an unfinished appearance. To successfully complete the work described above, it is recommended to think through the finishing step by step.

The finishing of the slopes and openings must correspond to the interior of the door and room

At the first stage, the support guides are processed. Then they are repainted in the same color as the door leaf. In case of severe wear, it is mounted on the guides plasterboard sheathing. If there are roughnesses, perforated corners are used for cladding. Then the opening is repainted.

In the future you will need to correctly. For their installation, special clamps are used that hold the platbands well. If there are no fasteners, glue or self-tapping screws are used.

If the door is updated only with the opening, and the slopes remain the same, then the decorating process is considered incomplete. Used for finishing slopes different methods. More often, special MDF strips are used to update slopes. You can also install plasterboard slopes, which are fixed on perforated corners or glue.

Another technique for finishing a slope is plastering. This process is the most labor-intensive and requires experience and qualifications in this matter. Experts believe that optimal solution is plastering followed by installation of perlite slopes, which are not cheap. But in the end you can get strong and durable slopes. Mold does not appear on them.

To equip doorways For bathrooms, products made from solid wood, chipboard or plastic are used. Operation of these products in conditions high humidity has a detrimental effect on the appearance of the canvas. It is not easy to dismantle the old structure and install a new one, given the current cost quality door. Therefore, many people have a question about how to finish inner door in the bathroom.

Preparing the door leaf for restoration

Before proceeding with restoration, it is recommended that you familiarize yourself with the stages of this work.

There are many ways to renew the surface of a door leaf, but regardless of the choice, first of all you will need to prepare a list of tools:

• Construction hair dryer;
• Plane;
• Spatula;
• Sanding machine;
• Sandpaper.

The first stage of work consists of processing and cleaning the canvas from the old coating.

Important! Removal of the old coating will be required regardless of what type of finishing is planned in the future.

Restoration work begins with removing the door from its hinges.

Removing the fabric from the hinges

The removed sash is laid on a previously prepared surface. The place for restoration of the product is chosen so that it is well lit and ventilated.

All elements are removed from the door so that a bare sheet remains. Subject to availability glass inserts, they also need to be carefully removed. After cleaning the canvas from excess elements, they begin to remove the old coating.

You can remove old paint using a variety of methods:

• If the canvas has a thin layer of paint, it is advisable to use a special remover, which is a chemical agent that contains acid. This method is considered the most gentle. Apply the remover using a brush to the door covering and wait certain time specified in the instructions for use. Soon the old coating will swell, after which it is removed with a spatula.

Chemical solution applied to old paint with a brush or roller

Important! When using chemical agent To clean the surface of the canvas, protect your hands and eyes from contact with the product.

• When many layers of paint have already been applied to the canvas, you will have to put in a lot of effort. In such cases, a special hair dryer is used. Under the influence of hot air, the coating will swell, after which it is also removed with a spatula. This method is quite effective, but sometimes due to careless work you can damage the surface of the door.

Removing old paint with a spatula using construction hair dryer

• If you don’t have a hair dryer, you can use another method. Place a damp, stiff cotton cloth on the door leaf and press down with a heated iron. After two minutes, remove the rag and iron, and clean off the paint with a spatula. This procedure is quite labor-intensive, and with its help it is difficult to remove paint from uneven areas on the canvas. At the same time, the fabric and the surface of the iron quickly become dirty, which will also have to be cleaned.

Updating the door leaf

The particles of the old coating remaining after cleaning are removed using sandpaper. First you need to go over the door leaf with coarse sandpaper, gradually moving to the “zero” sandpaper.

Important! Grinding work carried along the fibers to avoid the formation of transverse lines.

Sanding grinder

After sanding, the blade is inspected for various defects. Small cracks are removed using putty. Large depressions are more difficult to eliminate. In most cases, to eliminate large defects in the canvas, you will have to cut out the damaged fragment and prepare an overlay from wood. It is adjusted in size and attached to the canvas using glue. To eliminate minor gaps resulting from gluing, putty is also used.

With a varnished door, all manipulations with removing the old top layer are identical. Only one point differs - the choice of putty must be approached with special responsibility. Since the varnish is transparent, any imperfections will be visible underneath. The color of the canvas can be changed using varnish or stain.

Important! Internal laminated or veneered structures cannot be painted. Completely different methods are used for their restoration.

Designs of this kind can be updated using a special wax pencil.

Wax pencil, photo

The pencil is first heated, after which all scratches and cracks are treated. The main thing is to choose the right pencil tone to match the color of the door. If the material is chosen correctly, then all processed errors will become almost invisible.

Decor selection

The second stage is to directly select the type of decoration that will be used further.

Coloring

The easiest method of updating an old door is painting. But, given the features of the bathroom, you need to choose the right paint. It must be resistant to excessive humidity, temperature changes and not be afraid of frequent cleaning.

Painting MDF doors, photo

What paint is suitable for a bathroom door?

The range of paints is small; these are alkyd or acrylic compositions.

Advantages of alkyd paint:

• Ideal for painting MDF and chipboard;
• Available;
• Protects well from dampness;
• Not afraid of frequent washing;
• Has a wide color palette.

Disadvantages of alkyd paint:

• Professionals do not recommend using paint on structures made of natural wood.

Important! Wood has the ability to “breathe”, and alkyd compounds are vapor-tight.

This kind of coating delaminates quite quickly, resulting in cracks appearing on the surface.

• The smell of paint does not disappear for a long time.

Advantages of acrylic paint:

• Superior alkyd paints by service life;
• Not afraid of temperature changes and humidity;
• Easy to clean;
• No strong odor. There are compositions that are completely odorless.

Flaws:

• Despite the speed of paint drying, it remains susceptible to the slightest damage for a month.

Which paint should you prefer: glossy or matte?

There have been debates among professionals regarding the choice of paint type for a long time. According to their own decorative properties paints are divided into the following types:

• Matte;
• Glossy;
• Satin;
• Semi-gloss;
• Semi-matte.

The matte surface is the most unstable. This type of paint is completely unsuitable for covering door panels located in bathrooms due to high humidity. Glossy paint is also not very suitable for the bathroom, since it has excessive shine.

Painting the door leaf, photo

Important! If the shine of the canvas does not bother you, then it is quite possible to use this type of paint for the bathroom. Since with practical point vision, gloss becomes the best option. The smooth surface does not absorb dirt and is less prone to stains.

Semi-gloss and satin paints are an average and universal option.

After determining the type of paint, you can proceed to directly painting the door leaf. Key Rule- wise choice of color, since the painted door should be combined with the bathroom finishing elements. Apply paint with any in a convenient way in 2-3 layers.

Another option for door restoration is a combination of several colors. First, the canvas is covered with one color. After drying, it is sanded and a second shade is applied. You can create the desired texture using graters. After the canvas has dried, it is coated with varnish. A door finished in this way will take on a new life.

How to restore chipboard doors

This kind of material is not resistant to high humidity, so it is recommended to approach the restoration procedure responsibly. For this type of material, you should not use a hair dryer or sandpaper for sanding, as this can lead to surface deformation.

To remove the top layer of paint, you will have to resort to the “old-fashioned” method (iron and cloth) or use a remover. Use a spatula to very carefully remove the paint layer to avoid damaging the canvas.

Grinding is carried out only with a “zero”. After gentle manipulations, paint can be applied.

Important! The best option updating the chipboard structure - veneering.

Choosing the right paint is an important, but final step in restoring a structure. Equally important is careful painting, which is quite difficult to do without certain skills.

Comments

Unfortunately, there are no comments or reviews yet, but you can leave your...

New articles

New comments

S.A.

Grade

Svetlana

Grade

Sergey

Grade

Sergey

Grade

Alexey